Commercial Roof Coating
The general service for any commercial roof that is worn on top and dry underneath, from warehouses to retail strips.
View ServiceAll Services
Roof Coating Services in Owensboro
Ten Ways to Put a New Surface on an Old Commercial Roof
Our roof coating services in Owensboro cover metal, flat, single-ply, rubber, and asphalt roofs, plus spray foam and full restoration projects.
Pick by Roof
Our Roof Coating Services in Owensboro
Roof coating services in Owensboro start with the roof you have. Find your roof system or problem below and open its page for the details.
Silicone Roof Coating
Picked when a flat roof keeps water in low spots for a day or more after rain.
View ServiceAcrylic Roof Coating
Chosen for sloped metal and quick-draining roofs, applied in warm, dry weather.
View ServiceMetal Roof Coating
Covers screw-down and standing seam roofs on shops, barns, and warehouses after rust and fastener work.
View ServiceFlat Roof Coating
Handles low-slope roofs behind parapets, with scuppers, drains, and curbs rebuilt first.
View ServiceSpray Foam Roofing
Adds insulation and slope with polyurethane foam, finished under a protective top coat.
View ServiceTPO Roof Coating
Restores aged white single-ply once seams are welded or taped and a single-ply primer is down.
View ServiceEPDM Roof Coating
Turns black rubber white after chalking is scrubbed off and laps are reinforced.
View ServiceModified Bitumen Roof Coating
Seals granulated and built-up asphalt roofs after blister repair and a bleed-blocking primer.
View ServiceCommercial Roof Restoration
Bundles a moisture survey, wet-area replacement, detail rebuilds, and a full system into one project.
View ServiceSystem Guide
Which Coating System Fits Which Roof
Start with your roof type and how water behaves on it. The inspection confirms the choice.
| Your Roof | Common Choice | What Comes First |
|---|---|---|
| Flat roof that holds water | Silicone | Drains and low spots checked |
| Sloped metal roof | Acrylic over rust primer | Fasteners and laps sealed |
| Uninsulated metal shop | Spray foam with top coat | Panels secured, wind plan |
| Aged TPO membrane | Silicone or acrylic over single-ply primer | Seams welded or taped |
| Black EPDM rubber | White coating over EPDM primer | Chalking removed, laps reinforced |
| Modified bitumen or built-up | Coating over bleed-blocking primer | Blisters cut and patched |
| Roof with many leaks and patches | Full restoration | Moisture survey across the roof |
Not Sure Which Service Your Roof Needs?
Call and describe the roof and the building. We can point you to the right service before the inspection.
Process
One Owensboro Roof Coating Process for Every Service
Each service on this list runs through the same four stages, adjusted for the roof system.
Inspect Your Roof
Moisture readings, core cuts where needed, adhesion tests, and a drainage check show whether the roof can be coated and which service fits. You see the findings before any plan is set.
- Moisture readings
- Adhesion test
- Drainage check
Repair What the Inspection Found
Wet sections, open seams, failed flashing, loose fasteners, and blisters are repaired so the coating goes over a dry, closed roof.
- Wet sections replaced
- Seams and flashing repaired
- Fasteners secured
Prepare the Surface
Cleaning removes dirt, chalking, and loose granules, and primer goes on where the roof system needs help bonding or blocking bleed.
- Power wash and dry
- System-specific primer
- Intakes covered
Coat and Check Thickness
Coating is sprayed or rolled at the specified rate with extra passes on details. Thickness readings and a final walk close out the job.
- Details reinforced
- Field coated
- Final walk with you
FAQ
Questions About Owensboro Roof Coating
Answers that apply across our services.
Cost Questions
Do all coating services use the same price range?
Yes. Our ballpark estimate uses $2.50 to $4 per square foot for coating across these services, with roof condition, repairs, product, thickness, and access deciding where a roof lands.
Process Questions
Can more than one service apply to the same roof?
Often. A metal shop may get metal roof repairs plus spray foam, or a flat roof may need flat roof detail work plus a silicone system. The inspection sorts out the combination.
Coating Choice Questions
What is the difference between coating and restoration?
Coating is the system that goes on top. Restoration is the full project on a neglected roof, including the moisture survey, wet-area replacement, and detail rebuilds before the coating.
Which roof types can you coat?
We coat metal, TPO, EPDM, modified bitumen, smooth built-up, and spray foam roofs on Owensboro commercial buildings. Each system gets its own preparation: metal gets rust treatment and sealed fasteners, single-ply gets cleaning and a matched primer, and asphalt roofs get blister repair and a bleed-blocking primer. The TPO roof coating and EPDM roof coating services cover single-ply in detail.
Is spray foam roofing the same as a roof coating?
Spray foam roofing is a different system: polyurethane foam that insulates the roof and can add slope to low areas, with a coating sprayed over it to block sunlight. A roof coating alone is a thin liquid membrane that adds little insulation. Owensboro owners weigh foam against a coating on metal shops and flat roofs that hold water.
Next Step
Compare Roof Coating Services in Owensboro
Get a ballpark range for your roof, then let the inspection confirm which service fits.
